TOA VM-2120 VM-2000 Series Amplifier, 120W
The VM-2120 is a multifunctional amplifier that can be mounted in an EIA-Standard equipment rack (3-unit size). The unit comes with 4 audio inputs including the background music input, and the speaker output section which has an internal attenuator and 5-zone selector. It permits not only general-purpose broadcast, but also Emergency Broadcast based on the EN60849 Standard which gives pre-recorded voice instructions(*1) in emergency situation. Broadcast can be made from an optional RM-200M Remote Microphone as well as from the amplifier, and can be remotely controlled from external equipment. In addition, for 100 V/83 Ω application the unit features surveillance function(*2) which automatically checks the system for failures. (*1) An optional EV-200M Voice Announcement Board is required. (*2) An optional SV-200MA Surveillance Board is required.
Specification
Power Requirement AC mains, 50/60 Hz DC: 24 V
Output 120 W
Frequency Response 50 – 16,000 Hz
Distortion Less than 1%
Signal-to-Noise Ratio More than 60 dB
Tone Control Bass: 100 Hz ±10 dB, Treble: 10 kHz ±10 dB (Inputs 1 – 3 and BGM individually adjustable.)
Remote Microphone/Extension Amplifier Connection Two RJ45 female connectors Maximum distance: 800 m
Audio Input
Inputs 1 ~ 3 -60 dB*1 [MIC]/-10 dB*1 [LINE] (switchable), 600 Ω, electronically balanced*2, combined XLR type connector (female)/ 1/4″ phone jack (Only Input 1 is additionally (female)/ 1/4″ phone jack (Only Input 1 is additionally equipped with DIN connector*3.)
Telephone Paging Input Push-in terminal block
-10 dB*1, 10 k Ω, electronically-balanced*2
Control : No-voltage make contact input
BGM 1 – 2 -20 dB*1, 10 k Ω, RCA pin jack, monaural
Power Amplifier Input 0 dB*1, 10 k Ω, RCA pin jack
External Speaker Line Input 100 V line, for All-Zone Broadcast
Audio Output
Speaker Output 83 Ω (100 V line, volume control in maximum position), Removable terminal block with screw terminals.
Speaker Zone Control 5-zone selector with attenuator
Direct Speaker Line Output Direct output from the power amplifier output transformer
Line Output 0 dB*1, 10 k Ω, RCA pin jack
Recording Output 0 dB*1, 10 k Ω, RCA pin jack
Preamplifier Output 0 dB*1, 10 k Ω, RCA pin jack
Control Inputs 1 – 3 For controlling Inputs 1 – 3, Push-in terminal block
No-voltage make contact.
Control Input and Output Control Input and Output
Input : No-voltage make contact input
Output : Open collector output
(1) External control input
Activation of messages for an optional Voice Announcement Board*4
Activation of power
Activation and stop of Emergency Broadcast
Unit’s broadcast cutoff (when activated by an external emergency equipment)
(2) Status output
Irregularity of communications with the Remote Microphone and an expansion amplifier
AC power condition
DC power condition
Irregularity of the sound source of the Voice Announcement board
Stop of the unit’s broadcast
External Attenuator Control Output Removable terminal block with screw terminals, relay, no-voltage make contact output, transfer type
Surveillance Input and Output*5 25-pin female D-sub connector
Input : No-voltage make contact input
Output : Open collector output
Power Output 24 V DC
Chime Tone Built-in chime:
2-tone chime/2-tone chime(fast repeat)
4-tone chime (Up)/Single-tone chime/4-tone chime (Up & Down)/Gong/off
Finish Panel: ABS resin
Case: Steel plate painted
Dimensions 419 (W) × 143.3 (H) × 356.2 (D) mm
Notes *1 0 dB = 1 V
*2 Can be transformer-balanced with the addition of an optional IT-450 input transformer.
*3 For connection of the Paging Microphone with remote control switch.
*4 An optional EV-200 Voice Announcement Board is required.
*5 An optional SV-200M Surveillance Board is required.